BimmerFix Products Company official Website
Signed in as:
filler@godaddy.com
Answer: No, the BimmerFix® Stent is what is used to stop the common BMW® N62 Weep Hole leak. The aluminum alloy “Stent” creates an impenetrable, long lasting, repair. However, the BimmerFix® Cooling System Sealant and Conditioner can be added to the Cooling System, if desired, to stop leaks from the Rear Coolant Passage Cover (which requires the removal of the transmission to repair), and the Valley Pan Gasket. The Cooling System Sealer can also be added as a preventative measure and can remain in the Cooling System to help prevent future leaks.
Answer: No, it is not possible for a bad Rear O-ring to cause an external Engine Coolant leak. The Rear O-ring is a pressure neutral O-ring, and does not actually “seal” the Coolant from leaking outside of the Engine Block. The Rear O-ring is to provide cushioning and stability to the Coolant Transfer Pipe, so that the back side (rear side) of the Coolant Transfer Pipe does not vibrate and rattle around lose inside of the Engine Block.
Answer: The BimmerFix® Coolant Pipe Repair System can be purchased directly from our website by selecting the SHOP page. However, you can also purchase this item on eBay.com, (from the Seller ID BimmerFix®), and also at Amazon.com, (sold by BimmerFix® Products Company). The price for the complete BimmerFix® Coolant Pipe Repair System is the same on all websites, and includes free USPS Priority Mail (2-3 business days) shipping in the USA. USPS Express Mail (1 business day) and USPS International shipping is also available on all websites at an additional cost.
Answer: The best way to estimate the cost of installing the BimmerFix® Cooling Pipe Repair System is to ask your mechanic the cost of the shop labor and materials to replace the Water Pump (not including the actual cost of the Water Pump itself, unless this is to be replaced at the same time), and then add one or two hours of additional shop labor, to actually install the BimmerFix® Stent. Some Timing Chain Covers may require more sanding and preparation time that others, using the BimmerFix® Sanding Rod and Cleaning Rod (which are included with the kit). That is why we recommend allowing one or two hours of shop labor time for the installation of the actual BimmerFix® Stent
Answer: The BimmerFix® System can be installed by any auto repair shop or skilled do-it-yourself vehicle owner who can change the Water Pump. If your Mechanic is not familiar with the BimmerFix® System, they can call BimmerFix® Technical Support at (520) 544-4400. A list of auto repair shops that specialize in BMW repairs in the USA can be found at www.BimmerShops.com. If you are in Canada, go to www.ca.BimmerShops.com.
Answer: Yes. If there ever did come a time when the BimmerFix® Stent needed to be removed, it is possible to remove the Stent by removing the Water Pump, and then pulling the old Stent out, with a Hook Tool. BimmerFix® can provide this Hook Tool to Customers upon request. The Stent is held in place with a high quality, high temperature, high oil resistant silicone. The Stent is NOT permanently bonded or epoxied to the Timing Chain Cover or the Coolant Transfer Pipe.
BimmerFix Products Company 1-(520) 544-4400
This site is in no way associated with BMW ® North America, LLC. BimmerFix® Products Company is in no way affiliated or owned by BMW ® USA and/or BMW ® AG. The BimmerFix Coolant Pipe Repair System(TM) is protected by United States Patent US 10,240,513 B2 and other Patent(s) Pending and all rights are reserved. BimmerFix is a Registered Tradename with the United States Patent and Trademark Office.
Copyright © 2021 BimmerFix Products Co. - All Rights Reserved.
Powered by GoDaddy
We use cookies to analyze website traffic and optimize your website experience. By accepting our use of cookies, your data will be aggregated with all other user data.